How To Write Linux PCI Drivers by Martin Mares on 07-Feb-2000 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ The world of PCI is vast and it's full of (mostly unpleasant) surprises. Different PCI devices have different requirements and different bugs -- because of this, the PCI support layer in Linux kernel is not as trivial as one would wish. This short pamphlet tries to help all potential driver authors find their way through the deep forests of PCI handling. 0. Structure of PCI drivers ~~~~~~~~~~~~~~~~~~~~~~~~~~~ There exist two kinds of PCI drivers: new-style ones (which leave most of probing for devices to the PCI layer and support online insertion and removal of devices [thus supporting PCI, hot-pluggable PCI and CardBus in a single driver]) and old-style ones which just do all the probing themselves. Unless you have a very good reason to do so, please don't use the old way of probing in any new code. After the driver finds the devices it wishes to operate on (either the old or the new way), it needs to perform the following steps: Enable the device Access device configuration space Discover resources (addresses and IRQ numbers) provided by the device Allocate these resources Communicate with the device Most of these topics are covered by the following sections, for the rest look at , it's hopefully well commented. If the PCI subsystem is not configured (CONFIG_PCI is not set), most of the functions described below are defined as inline functions either completely empty or just returning an appropriate error codes to avoid lots of ifdefs in the drivers. 1. New-style drivers ~~~~~~~~~~~~~~~~~~~~ The new-style drivers just call pci_register_driver during their initialization with a pointer to a structure describing the driver (struct pci_driver) which contains: name Name of the driver id_table Pointer to table of device ID's the driver is interested in. Most drivers should export this table using MODULE_DEVICE_TABLE(pci,...). probe Pointer to a probing function which gets called (during execution of pci_register_driver for already existing devices or later if a new device gets inserted) for all PCI devices which match the ID table and are not handled by the other drivers yet. This function gets passed a pointer to the pci_dev structure representing the device and also which entry in the ID table did the device match. It returns zero when the driver has accepted the device or an error code (negative number) otherwise. This function always gets called from process context, so it can sleep. remove Pointer to a function which gets called whenever a device being handled by this driver is removed (either during deregistration of the driver or when it's manually pulled out of a hot-pluggable slot). This function always gets called from process context, so it can sleep. save_state Save a device's state before it's suspend. suspend Put device into low power state. resume Wake device from low power state. enable_wake Enable device to generate wake events from a low power state. (Please see Documentation/power/pci.txt for descriptions of PCI Power Management and the related functions) The ID table is an array of struct pci_device_id ending with a all-zero entry. Each entry consists of: vendor, device Vendor and device ID to match (or PCI_ANY_ID) subvendor, Subsystem vendor and device ID to match (or PCI_ANY_ID) subdevice class, Device class to match. The class_mask tells which bits class_mask of the class are honored during the comparison. driver_data Data private to the driver. Most drivers don't need to use the driver_data field. Best practice for use of driver_data is to use it as an index into a static list of equivalant device types, not to use it as a pointer. Have a table entry {PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID} to have probe() called for every PCI device known to the system. New PCI IDs may be added to a device driver at runtime by writing to the file /sys/bus/pci/drivers/{driver}/new_id. When added, the driver will probe for all devices it can support. echo "vendor device subvendor subdevice class class_mask driver_data" > \ /sys/bus/pci/drivers/{driver}/new_id where all fields are passed in as hexadecimal values (no leading 0x). Users need pass only as many fields as necessary; vendor, device, subvendor, and subdevice fields default to PCI_ANY_ID (FFFFFFFF), class and classmask fields default to 0, and driver_data defaults to 0UL. Device drivers must call pci_dynids_set_use_driver_data(pci_driver *, 1) in order for the driver_data field to get passed to the driver. Otherwise, only a 0 is passed in that field. When the driver exits, it just calls pci_unregister_driver() and the PCI layer automatically calls the remove hook for all devices handled by the driver. Please mark the initialization and cleanup functions where appropriate (the corresponding macros are defined in ): __init Initialization code. Thrown away after the driver initializes. __exit Exit code. Ignored for non-modular drivers. __devinit Device initialization code. Identical to __init if the kernel is not compiled with CONFIG_HOTPLUG, normal function otherwise. __devexit The same for __exit. Tips: The module_init()/module_exit() functions (and all initialization functions called only from these) should be marked __init/exit. The struct pci_driver shouldn't be marked with any of these tags. The ID table array should be marked __devinitdata. The probe() and remove() functions (and all initialization functions called only from these) should be marked __devinit/exit. If you are sure the driver is not a hotplug driver then use only __init/exit __initdata/exitdata. Pointers to functions marked as __devexit must be created using __devexit_p(function_name). That will generate the function name or NULL if the __devexit function will be discarded. 2. How to find PCI devices manually (the old style) ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ PCI drivers not using the pci_register_driver() interface search for PCI devices manually using the following constructs: Searching by vendor and device ID: struct pci_dev *dev = NULL; while (dev = pci_find_device(VENDOR_ID, DEVICE_ID, dev)) configure_device(dev); Searching by class ID (iterate in a similar way): pci_find_class(CLASS_ID, dev) Searching by both vendor/device and subsystem vendor/device ID: pci_find_subsys(VENDOR_ID, DEVICE_ID, SUBSYS_VENDOR_ID, SUBSYS_DEVICE_ID, dev). You can use the constant PCI_ANY_ID as a wildcard replacement for VENDOR_ID or DEVICE_ID. This allows searching for any device from a specific vendor, for example. Note that these functions are not hotplug-safe. Their hotplug-safe replacements are pci_get_device(), pci_get_class() and pci_get_subsys(). They increment the reference count on the pci_dev that they return. You must eventually (possibly at module unload) decrement the reference count on these devices by calling pci_dev_put(). 3. Enabling devices ~~~~~~~~~~~~~~~~~~~ Before you do anything with the device you've found, you need to enable it by calling pci_enable_device() which enables I/O and memory regions of the device, assigns missing resources if needed and wakes up the device if it was in suspended state. Please note that this function can fail. If you want to use the device in bus mastering mode, call pci_set_master() which enables the bus master bit in PCI_COMMAND register and also fixes the latency timer value if it's set to something bogus by the BIOS. If you want to use the PCI Memory-Write-Invalidate transaction, call pci_set_mwi(). This enables the PCI_COMMAND bit for Mem-Wr-Inval and also ensures that the cache line size register is set correctly. Make sure to check the return value of pci_set_mwi(), not all architectures may support Memory-Write-Invalidate. 4. How to access PCI config space ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ You can use pci_(read|write)_config_(byte|word|dword) to access the config space of a device represented by struct pci_dev *. All these functions return 0 when successful or an error code (PCIBIOS_...) which can be translated to a text string by pcibios_strerror. Most drivers expect that accesses to valid PCI devices don't fail. If you don't have a struct pci_dev available, you can call pci_bus_(read|write)_config_(byte|word|dword) to access a given device and function on that bus. If you access fields in the standard portion of the config header, please use symbolic names of locations and bits declared in . If you need to access Extended PCI Capability registers, just call pci_find_capability() for the particular capability and it will find the corresponding register block for you. 5. Addresses and interrupts ~~~~~~~~~~~~~~~~~~~~~~~~~~~ Memory and port addresses and interrupt numbers should NOT be read from the config space. You should use the values in the pci_dev structure as they might have been remapped by the kernel. See Documentation/IO-mapping.txt for how to access device memory. You still need to call request_region() for I/O regions and request_mem_region() for memory regions to make sure nobody else is using the same device. All interrupt handlers should be registered with SA_SHIRQ and use the devid to map IRQs to devices (remember that all PCI interrupts are shared). 6. Other interesting functions ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ pci_find_slot() Find pci_dev corresponding to given bus and slot numbers. pci_set_power_state() Set PCI Power Management state (0=D0 ... 3=D3) pci_find_capability() Find specified capability in device's capability list. pci_module_init() Inline helper function for ensuring correct pci_driver initialization and error handling. pci_resource_start() Returns bus start address for a given PCI region pci_resource_end() Returns bus end address for a given PCI region pci_resource_len() Returns the byte length of a PCI region pci_set_drvdata() Set private driver data pointer for a pci_dev pci_get_drvdata() Return private driver data pointer for a pci_dev pci_set_mwi() Enable Memory-Write-Invalidate transactions. pci_clear_mwi() Disable Memory-Write-Invalidate transactions. 7. Miscellaneous hints ~~~~~~~~~~~~~~~~~~~~~~ When displaying PCI slot names to the user (for example when a driver wants to tell the user what card has it found), please use pci_name(pci_dev) for this purpose. Always refer to the PCI devices by a pointer to the pci_dev structure. All PCI layer functions use this identification and it's the only reasonable one. Don't use bus/slot/function numbers except for very special purposes -- on systems with multiple primary buses their semantics can be pretty complex. If you're going to use PCI bus mastering DMA, take a look at Documentation/DMA-mapping.txt. Don't try to turn on Fast Back to Back writes in your driver. All devices on the bus need to be capable of doing it, so this is something which needs to be handled by platform and generic code, not individual drivers. 8. Obsolete functions ~~~~~~~~~~~~~~~~~~~~~ There are several functions which you might come across when trying to port an old driver to the new PCI interface. They are no longer present in the kernel as they aren't compatible with hotplug or PCI domains or having sane locking. pcibios_present() and Since ages, you don't need to test presence pci_present() of PCI subsystem when trying to talk to it. If it's not there, the list of PCI devices is empty and all functions for searching for devices just return NULL. pcibios_(read|write)_* Superseded by their pci_(read|write)_* counterparts. pcibios_find_* Superseded by their pci_find_* counterparts. pci_for_each_dev() Superseded by pci_find_device() pci_for_each_dev_reverse() Superseded by pci_find_device_reverse() pci_for_each_bus() Superseded by pci_find_next_bus() pci_find_device() Superseded by pci_get_device() pci_find_subsys() Superseded by pci_get_subsys() pcibios_find_class() Superseded by pci_find_class() pci_(read|write)_*_nodev() Superseded by pci_bus_(read|write)_*()