The Linux 2.4 Parallel Port Subsystem Tim Waugh
twaugh@redhat.com
1999-2000 Tim Waugh Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.1 or any later version published by the Free Software Foundation; with no Invariant Sections, with no Front-Cover Texts, and with no Back-Cover Texts. A copy of the license is included in the section entitled "GNU Free Documentation License".
Design goals The problems The first parallel port support for Linux came with the line printer driver, lp. The printer driver is a character special device, and (in Linux 2.0) had support for writing, via write, and configuration and statistics reporting via ioctl. The printer driver could be used on any computer that had an IBM PC-compatible parallel port. Because some architectures have parallel ports that aren't really the same as PC-style ports, other variants of the printer driver were written in order to support Amiga and Atari parallel ports. When the Iomega Zip drive was released, and a driver written for it, a problem became apparent. The Zip drive is a parallel port device that provides a parallel port of its own---it is designed to sit between a computer and an attached printer, with the printer plugged into the Zip drive, and the Zip drive plugged into the computer. The problem was that, although printers and Zip drives were both supported, for any given port only one could be used at a time. Only one of the two drivers could be present in the kernel at once. This was because of the fact that both drivers wanted to drive the same hardware---the parallel port. When the printer driver initialised, it would call the check_region function to make sure that the IO region associated with the parallel port was free, and then it would call request_region to allocate it. The Zip drive used the same mechanism. Whichever driver initialised first would gain exclusive control of the parallel port. The only way around this problem at the time was to make sure that both drivers were available as loadable kernel modules. To use the printer, load the printer driver module; then for the Zip drive, unload the printer driver module and load the Zip driver module. The net effect was that printing a document that was stored on a Zip drive was a bit of an ordeal, at least if the Zip drive and printer shared a parallel port. A better solution was needed. Zip drives are not the only devices that presented problems for Linux. There are other devices with pass-through ports, for example parallel port CD-ROM drives. There are also printers that report their status textually rather than using simple error pins: sending a command to the printer can cause it to report the number of pages that it has ever printed, or how much free memory it has, or whether it is running out of toner, and so on. The printer driver didn't originally offer any facility for reading back this information (although Carsten Gross added nibble mode readback support for kernel 2.2). The IEEE has issued a standards document called IEEE 1284, which documents existing practice for parallel port communications in a variety of modes. Those modes are: compatibility, reverse nibble, reverse byte, ECP and EPP. Newer devices often use the more advanced modes of transfer (ECP and EPP). In Linux 2.0, the printer driver only supported compatibility mode (i.e. normal printer protocol) and reverse nibble mode. The solutions The parport code in Linux 2.2 was designed to meet these problems of architectural differences in parallel ports, of port-sharing between devices with pass-through ports, and of lack of support for IEEE 1284 transfer modes. There are two layers to the parport subsystem, only one of which deals directly with the hardware. The other layer deals with sharing and IEEE 1284 transfer modes. In this way, parallel support for a particular architecture comes in the form of a module which registers itself with the generic sharing layer. The sharing model provided by the parport subsystem is one of exclusive access. A device driver, such as the printer driver, must ask the parport layer for access to the port, and can only use the port once access has been granted. When it has finished a transaction, it can tell the parport layer that it may release the port for other device drivers to use. Devices with pass-through ports all manage to share a parallel port with other devices in generally the same way. The device has a latch for each of the pins on its pass-through port. The normal state of affairs is pass-through mode, with the device copying the signal lines between its host port and its pass-through port. When the device sees a special signal from the host port, it latches the pass-through port so that devices further downstream don't get confused by the pass-through device's conversation with the host parallel port: the device connected to the pass-through port (and any devices connected in turn to it) are effectively cut off from the computer. When the pass-through device has completed its transaction with the computer, it enables the pass-through port again. This technique relies on certain special signals being invisible to devices that aren't watching for them. This tends to mean only changing the data signals and leaving the control signals alone. IEEE 1284.3 documents a standard protocol for daisy-chaining devices together with parallel ports. Support for standard transfer modes are provided as operations that can be performed on a port, along with operations for setting the data lines, or the control lines, or reading the status lines. These operations appear to the device driver as function pointers; more later. Standard transfer modes The standard transfer modes in use over the parallel port are defined by a document called IEEE 1284. It really just codifies existing practice and documents protocols (and variations on protocols) that have been in common use for quite some time. The original definitions of which pin did what were set out by Centronics Data Computer Corporation, but only the printer-side interface signals were specified. By the early 1980s, IBM's host-side implementation had become the most widely used. New printers emerged that claimed Centronics compatibility, but although compatible with Centronics they differed from one another in a number of ways. As a result of this, when IEEE 1284 was published in 1994, all that it could really do was document the various protocols that are used for printers (there are about six variations on a theme). In addition to the protocol used to talk to Centronics-compatible printers, IEEE 1284 defined other protocols that are used for unidirectional peripheral-to-host transfers (reverse nibble and reverse byte) and for fast bidirectional transfers (ECP and EPP). Structure Sharing core At the core of the parport subsystem is the sharing mechanism (see drivers/parport/share.c). This module, parport, is responsible for keeping track of which ports there are in the system, which device drivers might be interested in new ports, and whether or not each port is available for use (or if not, which driver is currently using it). Parports and their overrides The generic parport sharing code doesn't directly handle the parallel port hardware. That is done instead by low-level parport drivers. The function of a low-level parport driver is to detect parallel ports, register them with the sharing code, and provide a list of access functions for each port. The most basic access functions that must be provided are ones for examining the status lines, for setting the control lines, and for setting the data lines. There are also access functions for setting the direction of the data lines; normally they are in the forward direction (that is, the computer drives them), but some ports allow switching to reverse mode (driven by the peripheral). There is an access function for examining the data lines once in reverse mode. IEEE 1284 transfer modes Stacked on top of the sharing mechanism, but still in the parport module, are functions for transferring data. They are provided for the device drivers to use, and are very much like library routines. Since these transfer functions are provided by the generic parport core they must use the lowest common denominator set of access functions: they can set the control lines, examine the status lines, and use the data lines. With some parallel ports the data lines can only be set and not examined, and with other ports accessing the data register causes control line activity; with these types of situations, the IEEE 1284 transfer functions make a best effort attempt to do the right thing. In some cases, it is not physically possible to use particular IEEE 1284 transfer modes. The low-level parport drivers also provide IEEE 1284 transfer functions, as names in the access function list. The low-level driver can just name the generic IEEE 1284 transfer functions for this. Some parallel ports can do IEEE 1284 transfers in hardware; for those ports, the low-level driver can provide functions to utilise that feature. Pardevices and parport_drivers When a parallel port device driver (such as lp) initialises it tells the sharing layer about itself using parport_register_driver. The information is put into a struct parport_driver, which is put into a linked list. The information in a struct parport_driver really just amounts to some function pointers to callbacks in the parallel port device driver. During its initialisation, a low-level port driver tells the sharing layer about all the ports that it has found (using parport_register_port), and the sharing layer creates a struct parport for each of them. Each struct parport contains (among other things) a pointer to a struct parport_operations, which is a list of function pointers for the various operations that can be performed on a port. You can think of a struct parport as a parallel port object, if object-orientated programming is your thing. The parport structures are chained in a linked list, whose head is portlist (in drivers/parport/share.c). Once the port has been registered, the low-level port driver announces it. The parport_announce_port function walks down the list of parallel port device drivers (struct parport_drivers) calling the attach function of each (which may block). Similarly, a low-level port driver can undo the effect of registering a port with the parport_unregister_port function, and device drivers are notified using the detach callback (which may not block). Device drivers can undo the effect of registering themselves with the parport_unregister_driver function. The IEEE 1284.3 API The ability to daisy-chain devices is very useful, but if every device does it in a different way it could lead to lots of complications for device driver writers. Fortunately, the IEEE are standardising it in IEEE 1284.3, which covers daisy-chain devices and port multiplexors. At the time of writing, IEEE 1284.3 has not been published, but the draft specifies the on-the-wire protocol for daisy-chaining and multiplexing, and also suggests a programming interface for using it. That interface (or most of it) has been implemented in the parport code in Linux. At initialisation of the parallel port bus, daisy-chained devices are assigned addresses starting from zero. There can only be four devices with daisy-chain addresses, plus one device on the end that doesn't know about daisy-chaining and thinks it's connected directly to a computer. Another way of connecting more parallel port devices is to use a multiplexor. The idea is to have a device that is connected directly to a parallel port on a computer, but has a number of parallel ports on the other side for other peripherals to connect to (two or four ports are allowed). The multiplexor switches control to different ports under software control---it is, in effect, a programmable printer switch. Combining the ability of daisy-chaining five devices together with the ability to multiplex one parallel port between four gives the potential to have twenty peripherals connected to the same parallel port! In addition, of course, a single computer can have multiple parallel ports. So, each parallel port peripheral in the system can be identified with three numbers, or co-ordinates: the parallel port, the multiplexed port, and the daisy-chain address. Each device in the system is numbered at initialisation (by parport_daisy_init). You can convert between this device number and its co-ordinates with parport_device_num and parport_device_coords. #include <parport.h> int parport_device_num int parport int mux int daisy int parport_device_coords int devnum int *parport int *mux int *daisy Any parallel port peripheral will be connected directly or indirectly to a parallel port on the system, but it won't have a daisy-chain address if it does not know about daisy-chaining, and it won't be connected through a multiplexor port if there is no multiplexor. The special co-ordinate value -1 is used to indicate these cases. Two functions are provided for finding devices based on their IEEE 1284 Device ID: parport_find_device and parport_find_class. #include <parport.h> int parport_find_device const char *mfg const char *mdl int from int parport_find_class parport_device_class cls int from These functions take a device number (in addition to some other things), and return another device number. They walk through the list of detected devices until they find one that matches the requirements, and then return that device number (or -1 if there are no more such devices). They start their search at the device after the one in the list with the number given (at from+1, in other words). Device driver's view This section is written from the point of view of the device driver programmer, who might be writing a driver for a printer or a scanner or else anything that plugs into the parallel port. It explains how to use the parport interface to find parallel ports, use them, and share them with other device drivers. We'll start out with a description of the various functions that can be called, and then look at a reasonably simple example of their use: the printer driver. The interactions between the device driver and the parport layer are as follows. First, the device driver registers its existence with parport, in order to get told about any parallel ports that have been (or will be) detected. When it gets told about a parallel port, it then tells parport that it wants to drive a device on that port. Thereafter it can claim exclusive access to the port in order to talk to its device. So, the first thing for the device driver to do is tell parport that it wants to know what parallel ports are on the system. To do this, it uses the parport_register_driver function: #include <parport.h> struct parport_driver { const char *name; void (*attach) (struct parport *); void (*detach) (struct parport *); struct parport_driver *next; }; int parport_register_driver struct parport_driver *driver In other words, the device driver passes pointers to a couple of functions to parport, and parport calls attach for each port that's detected (and detach for each port that disappears---yes, this can happen). The next thing that happens is that the device driver tells parport that it thinks there's a device on the port that it can drive. This typically will happen in the driver's attach function, and is done with parport_register_device: #include <parport.h> struct pardevice *parport_register_device struct parport *port const char *name int (*pf) void * void (*kf) void * void (*irq_func) int, void *, struct pt_regs * int flags void *handle The port comes from the parameter supplied to the attach function when it is called, or alternatively can be found from the list of detected parallel ports directly with the (now deprecated) parport_enumerate function. A better way of doing this is with parport_find_number or parport_find_base functions, which find ports by number and by base I/O address respectively. #include <parport.h> struct parport *parport_find_number int number #include <parport.h> struct parport *parport_find_base unsigned long base The next three parameters, pf, kf, and irq_func, are more function pointers. These callback functions get called under various circumstances, and are always given the handle as one of their parameters. The preemption callback, pf, is called when the driver has claimed access to the port but another device driver wants access. If the driver is willing to let the port go, it should return zero and the port will be released on its behalf. There is no need to call parport_release. If pf gets called at a bad time for letting the port go, it should return non-zero and no action will be taken. It is good manners for the driver to try to release the port at the earliest opportunity after its preemption callback is called. The kick callback, kf, is called when the port can be claimed for exclusive access; that is, parport_claim is guaranteed to succeed inside the kick callback. If the driver wants to claim the port it should do so; otherwise, it need not take any action. The irq_func callback is called, predictably, when a parallel port interrupt is generated. But it is not the only code that hooks on the interrupt. The sequence is this: the lowlevel driver is the one that has done request_irq; it then does whatever hardware-specific things it needs to do to the parallel port hardware (for PC-style ports, there is nothing special to do); it then tells the IEEE 1284 code about the interrupt, which may involve reacting to an IEEE 1284 event, depending on the current IEEE 1284 phase; and finally the irq_func function is called. None of the callback functions are allowed to block. The flags are for telling parport any requirements or hints that are useful. The only useful value here (other than 0, which is the usual value) is PARPORT_DEV_EXCL. The point of that flag is to request exclusive access at all times---once a driver has successfully called parport_register_device with that flag, no other device drivers will be able to register devices on that port (until the successful driver deregisters its device, of course). The PARPORT_DEV_EXCL flag is for preventing port sharing, and so should only be used when sharing the port with other device drivers is impossible and would lead to incorrect behaviour. Use it sparingly! Devices can also be registered by device drivers based on their device numbers (the same device numbers as in the previous section). The parport_open function is similar to parport_register_device, and parport_close is the equivalent of parport_unregister_device. The difference is that parport_open takes a device number rather than a pointer to a struct parport. #include <parport.h> struct pardevice *parport_open int devnum const char *name int (*pf) void * int (*kf) void * int (*irqf) int, void *, struct pt_regs * int flags void *handle void parport_close struct pardevice *dev struct pardevice *parport_register_device struct parport *port const char *name int (*pf) void * int (*kf) void * int (*irqf) int, void *, struct pt_regs * int flags void *handle void parport_unregister_device struct pardevice *dev The intended use of these functions is during driver initialisation while the driver looks for devices that it supports, as demonstrated by the following code fragment: Once your device driver has registered its device and been handed a pointer to a struct pardevice, the next thing you are likely to want to do is communicate with the device you think is there. To do that you'll need to claim access to the port. #include <parport.h> int parport_claim struct pardevice *dev int parport_claim_or_block struct pardevice *dev void parport_release struct pardevice *dev To claim access to the port, use parport_claim or parport_claim_or_block. The first of these will not block, and so can be used from interrupt context. If parport_claim succeeds it will return zero and the port is available to use. It may fail (returning non-zero) if the port is in use by another driver and that driver is not willing to relinquish control of the port. The other function, parport_claim_or_block, will block if necessary to wait for the port to be free. If it slept, it returns 1; if it succeeded without needing to sleep it returns 0. If it fails it will return a negative error code. When you have finished communicating with the device, you can give up access to the port so that other drivers can communicate with their devices. The parport_release function cannot fail, but it should not be called without the port claimed. Similarly, you should not try to claim the port if you already have it claimed. You may find that although there are convenient points for your driver to relinquish the parallel port and allow other drivers to talk to their devices, it would be preferable to keep hold of the port. The printer driver only needs the port when there is data to print, for example, but a network driver (such as PLIP) could be sent a remote packet at any time. With PLIP, it is no huge catastrophe if a network packet is dropped, since it will likely be sent again, so it is possible for that kind of driver to share the port with other (pass-through) devices. The parport_yield and parport_yield_blocking functions are for marking points in the driver at which other drivers may claim the port and use their devices. Yielding the port is similar to releasing it and reclaiming it, but is more efficient because nothing is done if there are no other devices needing the port. In fact, nothing is done even if there are other devices waiting but the current device is still within its timeslice. The default timeslice is half a second, but it can be adjusted via a /proc entry. #include <parport.h> int parport_yield struct pardevice *dev int parport_yield_blocking struct pardevice *dev The first of these, parport_yield, will not block but as a result may fail. The return value for parport_yield is the same as for parport_claim. The blocking version, parport_yield_blocking, has the same return code as parport_claim_or_block. Once the port has been claimed, the device driver can use the functions in the struct parport_operations pointer in the struct parport it has a pointer to. For example: ops->write_data (port, d); ]]> Some of these operations have shortcuts. For instance, parport_write_data is equivalent to the above, but may be a little bit faster (it's a macro that in some cases can avoid needing to indirect through port and ops). Port drivers To recap, then: The device driver registers itself with parport. A low-level driver finds a parallel port and registers it with parport (these first two things can happen in either order). This registration creates a struct parport which is linked onto a list of known ports. parport calls the attach function of each registered device driver, passing it the pointer to the new struct parport. The device driver gets a handle from parport, for use with parport_claim/release. This handle takes the form of a pointer to a struct pardevice, representing a particular device on the parallel port, and is acquired using parport_register_device. The device driver claims the port using parport_claim (or function_claim_or_block). Then it goes ahead and uses the port. When finished it releases the port. The purpose of the low-level drivers, then, is to detect parallel ports and provide methods of accessing them (i.e. implementing the operations in struct parport_operations). A more complete description of which operation is supposed to do what is available in Documentation/parport-lowlevel.txt. The printer driver The printer driver, lp is a character special device driver and a parport client. As a character special device driver it registers a struct file_operations using register_chrdev, with pointers filled in for write, ioctl, open and release. As a client of parport, it registers a struct parport_driver using parport_register_driver, so that parport knows to call lp_attach when a new parallel port is discovered (and lp_detach when it goes away). The parallel port console functionality is also implemented in drivers/char/lp.c, but that won't be covered here (it's quite simple though). The initialisation of the driver is quite easy to understand (see lp_init). The lp_table is an array of structures that contain information about a specific device (the struct pardevice associated with it, for example). That array is initialised to sensible values first of all. Next, the printer driver calls register_chrdev passing it a pointer to lp_fops, which contains function pointers for the printer driver's implementation of open, write, and so on. This part is the same as for any character special device driver. After successfully registering itself as a character special device driver, the printer driver registers itself as a parport client using parport_register_driver. It passes a pointer to this structure: The lp_detach function is not very interesting (it does nothing); the interesting bit is lp_attach. What goes on here depends on whether the user supplied any parameters. The possibilities are: no parameters supplied, in which case the printer driver uses every port that is detected; the user supplied the parameter auto, in which case only ports on which the device ID string indicates a printer is present are used; or the user supplied a list of parallel port numbers to try, in which case only those are used. For each port that the printer driver wants to use (see lp_register), it calls parport_register_device and stores the resulting struct pardevice pointer in the lp_table. If the user told it to do so, it then resets the printer. The other interesting piece of the printer driver, from the point of view of parport, is lp_write. In this function, the user space process has data that it wants printed, and the printer driver hands it off to the parport code to deal with. The parport functions it uses that we have not seen yet are parport_negotiate, parport_set_timeout, and parport_write. These functions are part of the IEEE 1284 implementation. The way the IEEE 1284 protocol works is that the host tells the peripheral what transfer mode it would like to use, and the peripheral either accepts that mode or rejects it; if the mode is rejected, the host can try again with a different mode. This is the negotiation phase. Once the peripheral has accepted a particular transfer mode, data transfer can begin that mode. The particular transfer mode that the printer driver wants to use is named in IEEE 1284 as compatibility mode, and the function to request a particular mode is called parport_negotiate. #include <parport.h> int parport_negotiate struct parport *port int mode The modes parameter is a symbolic constant representing an IEEE 1284 mode; in this instance, it is IEEE1284_MODE_COMPAT. (Compatibility mode is slightly different to the other modes---rather than being specifically requested, it is the default until another mode is selected.) Back to lp_write then. First, access to the parallel port is secured with parport_claim_or_block. At this point the driver might sleep, waiting for another driver (perhaps a Zip drive driver, for instance) to let the port go. Next, it goes to compatibility mode using parport_negotiate. The main work is done in the write-loop. In particular, the line that hands the data over to parport reads: The parport_write function writes data to the peripheral using the currently selected transfer mode (compatibility mode, in this case). It returns the number of bytes successfully written: #include <parport.h> ssize_t parport_write struct parport *port const void *buf size_t len ssize_t parport_read struct parport *port void *buf size_t len (parport_read does what it sounds like, but only works for modes in which reverse transfer is possible. Of course, parport_write only works in modes in which forward transfer is possible, too.) The buf pointer should be to kernel space memory, and obviously the len parameter specifies the amount of data to transfer. In fact what parport_write does is call the appropriate block transfer function from the struct parport_operations: The transfer code in parport will tolerate a data transfer stall only for so long, and this timeout can be specified with parport_set_timeout, which returns the previous timeout: #include <parport.h> long parport_set_timeout struct pardevice *dev long inactivity This timeout is specific to the device, and is restored on parport_claim. The next function to look at is the one that allows processes to read from /dev/lp0: lp_read. It's short, like lp_write. The semantics of reading from a line printer device are as follows: Switch to reverse nibble mode. Try to read data from the peripheral using reverse nibble mode, until either the user-provided buffer is full or the peripheral indicates that there is no more data. If there was data, stop, and return it. Otherwise, we tried to read data and there was none. If the user opened the device node with the O_NONBLOCK flag, return. Otherwise wait until an interrupt occurs on the port (or a timeout elapses). User-level device drivers Introduction to ppdev The printer is accessible through /dev/lp0; in the same way, the parallel port itself is accessible through /dev/parport0. The difference is in the level of control that you have over the wires in the parallel port cable. With the printer driver, a user-space program (such as the printer spooler) can send bytes in printer protocol. Briefly, this means that for each byte, the eight data lines are set up, then a strobe line tells the printer to look at the data lines, and the printer sets an acknowledgement line to say that it got the byte. The printer driver also allows the user-space program to read bytes in nibble mode, which is a way of transferring data from the peripheral to the computer half a byte at a time (and so it's quite slow). In contrast, the ppdev driver (accessed via /dev/parport0) allows you to: examine status lines, set control lines, set/examine data lines (and control the direction of the data lines), wait for an interrupt (triggered by one of the status lines), find out how many new interrupts have occurred, set up a response to an interrupt, use IEEE 1284 negotiation (for telling peripheral which transfer mode, to use) transfer data using a specified IEEE 1284 mode. User-level or kernel-level driver? The decision of whether to choose to write a kernel-level device driver or a user-level device driver depends on several factors. One of the main ones from a practical point of view is speed: kernel-level device drivers get to run faster because they are not preemptable, unlike user-level applications. Another factor is ease of development. It is in general easier to write a user-level driver because (a) one wrong move does not result in a crashed machine, (b) you have access to user libraries (such as the C library), and (c) debugging is easier. Programming interface The ppdev interface is largely the same as that of other character special devices, in that it supports open, close, read, write, and ioctl. The constants for the ioctl commands are in include/linux/ppdev.h. Starting and stopping: <function>open</function> and <function>close</function> The device node /dev/parport0 represents any device that is connected to parport0, the first parallel port in the system. Each time the device node is opened, it represents (to the process doing the opening) a different device. It can be opened more than once, but only one instance can actually be in control of the parallel port at any time. A process that has opened /dev/parport0 shares the parallel port in the same way as any other device driver. A user-land driver may be sharing the parallel port with in-kernel device drivers as well as other user-land drivers. Control: <function>ioctl</function> Most of the control is done, naturally enough, via the ioctl call. Using ioctl, the user-land driver can control both the ppdev driver in the kernel and the physical parallel port itself. The ioctl call takes as parameters a file descriptor (the one returned from opening the device node), a command, and optionally (a pointer to) some data. PPCLAIM Claims access to the port. As a user-land device driver writer, you will need to do this before you are able to actually change the state of the parallel port in any way. Note that some operations only affect the ppdev driver and not the port, such as PPSETMODE; they can be performed while access to the port is not claimed. PPEXCL Instructs the kernel driver to forbid any sharing of the port with other drivers, i.e. it requests exclusivity. The PPEXCL command is only valid when the port is not already claimed for use, and it may mean that the next PPCLAIM ioctl will fail: some other driver may already have registered itself on that port. Most device drivers don't need exclusive access to the port. It's only provided in case it is really needed, for example for devices where access to the port is required for extensive periods of time (many seconds). Note that the PPEXCL ioctl doesn't actually claim the port there and then---action is deferred until the PPCLAIM ioctl is performed. PPRELEASE Releases the port. Releasing the port undoes the effect of claiming the port. It allows other device drivers to talk to their devices (assuming that there are any). PPYIELD Yields the port to another driver. This ioctl is a kind of short-hand for releasing the port and immediately reclaiming it. It gives other drivers a chance to talk to their devices, but afterwards claims the port back. An example of using this would be in a user-land printer driver: once a few characters have been written we could give the port to another device driver for a while, but if we still have characters to send to the printer we would want the port back as soon as possible. It is important not to claim the parallel port for too long, as other device drivers will have no time to service their devices. If your device does not allow for parallel port sharing at all, it is better to claim the parallel port exclusively (see PPEXCL). PPNEGOT Performs IEEE 1284 negotiation into a particular mode. Briefly, negotiation is the method by which the host and the peripheral decide on a protocol to use when transferring data. An IEEE 1284 compliant device will start out in compatibility mode, and then the host can negotiate to another mode (such as ECP). The ioctl parameter should be a pointer to an int; values for this are in incluce/linux/parport.h and include: IEEE1284_MODE_COMPAT IEEE1284_MODE_NIBBLE IEEE1284_MODE_BYTE IEEE1284_MODE_EPP IEEE1284_MODE_ECP The PPNEGOT ioctl actually does two things: it performs the on-the-wire negotiation, and it sets the behaviour of subsequent read/write calls so that they use that mode (but see PPSETMODE). PPSETMODE Sets which IEEE 1284 protocol to use for the read and write calls. The ioctl parameter should be a pointer to an int. PPGETMODE Retrieves the current IEEE 1284 mode to use for read and write. PPGETTIME Retrieves the time-out value. The read and write calls will time out if the peripheral doesn't respond quickly enough. The PPGETTIME ioctl retrieves the length of time that the peripheral is allowed to have before giving up. The ioctl parameter should be a pointer to a struct timeval. PPSETTIME Sets the time-out. The ioctl parameter should be a pointer to a struct timeval. PPGETMODES Retrieves the capabilities of the hardware (i.e. the modes field of the parport structure). PPSETFLAGS Sets flags on the ppdev device which can affect future I/O operations. Available flags are: PP_FASTWRITE PP_FASTREAD PP_W91284PIC PPWCONTROL Sets the control lines. The ioctl parameter is a pointer to an unsigned char, the bitwise OR of the control line values in include/linux/parport.h. PPRCONTROL Returns the last value written to the control register, in the form of an unsigned char: each bit corresponds to a control line (although some are unused). The ioctl parameter should be a pointer to an unsigned char. This doesn't actually touch the hardware; the last value written is remembered in software. This is because some parallel port hardware does not offer read access to the control register. The control lines bits are defined in include/linux/parport.h: PARPORT_CONTROL_STROBE PARPORT_CONTROL_AUTOFD PARPORT_CONTROL_SELECT PARPORT_CONTROL_INIT PPFCONTROL Frobs the control lines. Since a common operation is to change one of the control signals while leaving the others alone, it would be quite inefficient for the user-land driver to have to use PPRCONTROL, make the change, and then use PPWCONTROL. Of course, each driver could remember what state the control lines are supposed to be in (they are never changed by anything else), but in order to provide PPRCONTROL, ppdev must remember the state of the control lines anyway. The PPFCONTROL ioctl is for frobbing control lines, and is like PPWCONTROL but acts on a restricted set of control lines. The ioctl parameter is a pointer to a struct ppdev_frob_struct: The mask and val fields are bitwise ORs of control line names (such as in PPWCONTROL). The operation performed by PPFCONTROL is: In other words, the signals named in mask are set to the values in val. PPRSTATUS Returns an unsigned char containing bits set for each status line that is set (for instance, PARPORT_STATUS_BUSY). The ioctl parameter should be a pointer to an unsigned char. PPDATADIR Controls the data line drivers. Normally the computer's parallel port will drive the data lines, but for byte-wide transfers from the peripheral to the host it is useful to turn off those drivers and let the peripheral drive the signals. (If the drivers on the computer's parallel port are left on when this happens, the port might be damaged.) This is only needed in conjunction with PPWDATA or PPRDATA. The ioctl parameter is a pointer to an int. If the int is zero, the drivers are turned on (forward direction); if non-zero, the drivers are turned off (reverse direction). PPWDATA Sets the data lines (if in forward mode). The ioctl parameter is a pointer to an unsigned char. PPRDATA Reads the data lines (if in reverse mode). The ioctl parameter is a pointer to an unsigned char. PPCLRIRQ Clears the interrupt count. The ppdev driver keeps a count of interrupts as they are triggered. PPCLRIRQ stores this count in an int, a pointer to which is passed in as the ioctl parameter. In addition, the interrupt count is reset to zero. PPWCTLONIRQ Set a trigger response. Afterwards when an interrupt is triggered, the interrupt handler will set the control lines as requested. The ioctl parameter is a pointer to an unsigned char, which is interpreted in the same way as for PPWCONTROL. The reason for this ioctl is simply speed. Without this ioctl, responding to an interrupt would start in the interrupt handler, switch context to the user-land driver via poll or select, and then switch context back to the kernel in order to handle PPWCONTROL. Doing the whole lot in the interrupt handler is a lot faster. Transferring data: <function>read</function> and <function>write</function> Transferring data using read and write is straightforward. The data is transferring using the current IEEE 1284 mode (see the PPSETMODE ioctl). For modes which can only transfer data in one direction, only the appropriate function will work, of course. Waiting for events: <function>poll</function> and <function>select</function> The ppdev driver provides user-land device drivers with the ability to wait for interrupts, and this is done using poll (and select, which is implemented in terms of poll). When a user-land device driver wants to wait for an interrupt, it sleeps with poll. When the interrupt arrives, ppdev wakes it up (with a read event, although strictly speaking there is nothing to actually read). Examples Presented here are two demonstrations of how to write a simple printer driver for ppdev. Firstly we will use the write function, and after that we will drive the control and data lines directly. The first thing to do is to actually open the device. Here name should be something along the lines of "/dev/parport0". (If you don't have any /dev/parport files, you can make them with mknod; they are character special device nodes with major 99.) In order to do anything with the port we need to claim access to it. Our printer driver will copy its input (from stdin) to the printer, and it can do that it one of two ways. The first way is to hand it all off to the kernel driver, with the knowledge that the protocol that the printer speaks is IEEE 1284's compatibility mode. 0) { int written = write_printer (fd, ptr, got); if (written < 0) { perror ("write"); close (fd); return 1; } ptr += written; got -= written; } } ]]> The write_printer function is not pictured above. This is because the main loop that is shown can be used for both methods of driving the printer. Here is one implementation of write_printer: We hand the data to the kernel-level driver (using write) and it handles the printer protocol. Now let's do it the hard way! In this particular example there is no practical reason to do anything other than just call write, because we know that the printer talks an IEEE 1284 protocol. On the other hand, this particular example does not even need a user-land driver since there is already a kernel-level one; for the purpose of this discussion, try to imagine that the printer speaks a protocol that is not already implemented under Linux. So, here is the alternative implementation of write_printer (for brevity, error checking has been omitted): To show a bit more of the ppdev interface, here is a small piece of code that is intended to mimic the printer's side of printer protocol. 1) fprintf (stderr, "Arghh! Missed %d interrupt%s!\n", irqc - 1, irqc == 2 ? "s" : ""); /* Ack it. */ ioctl (fd, PPWCONTROL, &acking); usleep (2); ioctl (fd, PPWCONTROL, &busy); putchar (ch); } ]]> And here is an example (with no error checking at all) to show how to read data from the port, using ECP mode, with optional negotiation to ECP mode first. Linux parallel port driver API reference !Fdrivers/parport/daisy.c parport_device_num !Fdrivers/parport/daisy.c parport_device_coords !Fdrivers/parport/daisy.c parport_find_device !Fdrivers/parport/daisy.c parport_find_class !Fdrivers/parport/share.c parport_register_driver !Fdrivers/parport/share.c parport_unregister_driver !Fdrivers/parport/share.c parport_get_port !Fdrivers/parport/share.c parport_put_port !Fdrivers/parport/share.c parport_find_number parport_find_base !Fdrivers/parport/share.c parport_register_device !Fdrivers/parport/share.c parport_unregister_device !Fdrivers/parport/daisy.c parport_open !Fdrivers/parport/daisy.c parport_close !Fdrivers/parport/share.c parport_claim !Fdrivers/parport/share.c parport_claim_or_block !Fdrivers/parport/share.c parport_release !Finclude/linux/parport.h parport_yield !Finclude/linux/parport.h parport_yield_blocking !Fdrivers/parport/ieee1284.c parport_negotiate !Fdrivers/parport/ieee1284.c parport_write !Fdrivers/parport/ieee1284.c parport_read !Fdrivers/parport/ieee1284.c parport_set_timeout The Linux 2.2 Parallel Port Subsystem Although the interface described in this document is largely new with the 2.4 kernel, the sharing mechanism is available in the 2.2 kernel as well. The functions available in 2.2 are: parport_register_device parport_unregister_device parport_claim parport_claim_or_block parport_release parport_yield parport_yield_blocking In addition, negotiation to reverse nibble mode is supported: int parport_ieee1284_nibble_mode_ok struct parport *port unsigned char mode The only valid values for mode are 0 (for reverse nibble mode) and 4 (for Device ID in reverse nibble mode). This function is obsoleted by parport_negotiate in Linux 2.4, and has been removed. GNU Free Documentation License GNU Free Documentation License Version 1.1, March 2000 Copyright (C) 2000 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. 0. PREAMBLE The purpose of this License is to make a manual, textbook, or other written document "free" in the sense of freedom: to assure everyone the effective freedom to copy and redistribute it, with or without modifying it, either commercially or noncommercially. Secondarily, this License preserves for the author and publisher a way to get credit for their work, while not being considered responsible for modifications made by others. This License is a kind of "copyleft", which means that derivative works of the document must themselves be free in the same sense. It complements the GNU General Public License, which is a copyleft license designed for free software. We have designed this License in order to use it for manuals for free software, because free software needs free documentation: a free program should come with manuals providing the same freedoms that the software does. But this License is not limited to software manuals; it can be used for any textual work, regardless of subject matter or whether it is published as a printed book. We recommend this License principally for works whose purpose is instruction or reference. 1. APPLICABILITY AND DEFINITIONS This License applies to any manual or other work that contains a notice placed by the copyright holder saying it can be distributed under the terms of this License. The "Document", below, refers to any such manual or work. Any member of the public is a licensee, and is addressed as "you". A "Modified Version" of the Document means any work containing the Document or a portion of it, either copied verbatim, or with modifications and/or translated into another language. A "Secondary Section" is a named appendix or a front-matter section of the Document that deals exclusively with the relationship of the publishers or authors of the Document to the Document's overall subject (or to related matters) and contains nothing that could fall directly within that overall subject. (For example, if the Document is in part a textbook of mathematics, a Secondary Section may not explain any mathematics.) The relationship could be a matter of historical connection with the subject or with related matters, or of legal, commercial, philosophical, ethical or political position regarding them. The "Invariant Sections" are certain Secondary Sections whose titles are designated, as being those of Invariant Sections, in the notice that says that the Document is released under this License. The "Cover Texts" are certain short passages of text that are listed, as Front-Cover Texts or Back-Cover Texts, in the notice that says that the Document is released under this License. A "Transparent" copy of the Document means a machine-readable copy, represented in a format whose specification is available to the general public, whose contents can be viewed and edited directly and straightforwardly with generic text editors or (for images composed of pixels) generic paint programs or (for drawings) some widely available drawing editor, and that is suitable for input to text formatters or for automatic translation to a variety of formats suitable for input to text formatters. A copy made in an otherwise Transparent file format whose markup has been designed to thwart or discourage subsequent modification by readers is not Transparent. A copy that is not "Transparent" is called "Opaque". Examples of suitable formats for Transparent copies include plain ASCII without markup, Texinfo input format, LaTeX input format, SGML or XML using a publicly available DTD, and standard-conforming simple HTML designed for human modification. Opaque formats include PostScript, PDF, proprietary formats that can be read and edited only by proprietary word processors, SGML or XML for which the DTD and/or processing tools are not generally available, and the machine-generated HTML produced by some word processors for output purposes only. The "Title Page" means, for a printed book, the title page itself, plus such following pages as are needed to hold, legibly, the material this License requires to appear in the title page. For works in formats which do not have any title page as such, "Title Page" means the text near the most prominent appearance of the work's title, preceding the beginning of the body of the text. 2. VERBATIM COPYING You may copy and distribute the Document in any medium, either commercially or noncommercially, provided that this License, the copyright notices, and the license notice saying this License applies to the Document are reproduced in all copies, and that you add no other conditions whatsoever to those of this License. You may not use technical measures to obstruct or control the reading or further copying of the copies you make or distribute. However, you may accept compensation in exchange for copies. If you distribute a large enough number of copies you must also follow the conditions in section 3. You may also lend copies, under the same conditions stated above, and you may publicly display copies. 3. COPYING IN QUANTITY If you publish printed copies of the Document numbering more than 100, and the Document's license notice requires Cover Texts, you must enclose the copies in covers that carry, clearly and legibly, all these Cover Texts: Front-Cover Texts on the front cover, and Back-Cover Texts on the back cover. Both covers must also clearly and legibly identify you as the publisher of these copies. The front cover must present the full title with all words of the title equally prominent and visible. You may add other material on the covers in addition. Copying with changes limited to the covers, as long as they preserve the title of the Document and satisfy these conditions, can be treated as verbatim copying in other respects. If the required texts for either cover are too voluminous to fit legibly, you should put the first ones listed (as many as fit reasonably) on the actual cover, and continue the rest onto adjacent pages. If you publish or distribute Opaque copies of the Document numbering more than 100, you must either include a machine-readable Transparent copy along with each Opaque copy, or state in or with each Opaque copy a publicly-accessible computer-network location containing a complete Transparent copy of the Document, free of added material, which the general network-using public has access to download anonymously at no charge using public-standard network protocols. If you use the latter option, you must take reasonably prudent steps, when you begin distribution of Opaque copies in quantity, to ensure that this Transparent copy will remain thus accessible at the stated location until at least one year after the last time you distribute an Opaque copy (directly or through your agents or retailers) of that edition to the public. It is requested, but not required, that you contact the authors of the Document well before redistributing any large number of copies, to give them a chance to provide you with an updated version of the Document. 4. MODIFICATIONS You may copy and distribute a Modified Version of the Document under the conditions of sections 2 and 3 above, provided that you release the Modified Version under precisely this License, with the Modified Version filling the role of the Document, thus licensing distribution and modification of the Modified Version to whoever possesses a copy of it. In addition, you must do these things in the Modified Version: A. Use in the Title Page (and on the covers, if any) a title distinct from that of the Document, and from those of previous versions (which should, if there were any, be listed in the History section of the Document). You may use the same title as a previous version if the original publisher of that version gives permission. B. List on the Title Page, as authors, one or more persons or entities responsible for authorship of the modifications in the Modified Version, together with at least five of the principal authors of the Document (all of its principal authors, if it has less than five). C. State on the Title page the name of the publisher of the Modified Version, as the publisher. D. Preserve all the copyright notices of the Document. E. Add an appropriate copyright notice for your modifications adjacent to the other copyright notices. F. Include, immediately after the copyright notices, a license notice giving the public permission to use the Modified Version under the terms of this License, in the form shown in the Addendum below. G. Preserve in that license notice the full lists of Invariant Sections and required Cover Texts given in the Document's license notice. H. Include an unaltered copy of this License. I. Preserve the section entitled "History", and its title, and add to it an item stating at least the title, year, new authors, and publisher of the Modified Version as given on the Title Page. If there is no section entitled "History" in the Document, create one stating the title, year, authors, and publisher of the Document as given on its Title Page, then add an item describing the Modified Version as stated in the previous sentence. J. Preserve the network location, if any, given in the Document for public access to a Transparent copy of the Document, and likewise the network locations given in the Document for previous versions it was based on. These may be placed in the "History" section. You may omit a network location for a work that was published at least four years before the Document itself, or if the original publisher of the version it refers to gives permission. K. In any section entitled "Acknowledgements" or "Dedications", preserve the section's title, and preserve in the section all the substance and tone of each of the contributor acknowledgements and/or dedications given therein. L. Preserve all the Invariant Sections of the Document, unaltered in their text and in their titles. Section numbers or the equivalent are not considered part of the section titles. M. Delete any section entitled "Endorsements". Such a section may not be included in the Modified Version. N. Do not retitle any existing section as "Endorsements" or to conflict in title with any Invariant Section. If the Modified Version includes new front-matter sections or appendices that qualify as Secondary Sections and contain no material copied from the Document, you may at your option designate some or all of these sections as invariant. To do this, add their titles to the list of Invariant Sections in the Modified Version's license notice. These titles must be distinct from any other section titles. You may add a section entitled "Endorsements", provided it contains nothing but endorsements of your Modified Version by various parties--for example, statements of peer review or that the text has been approved by an organization as the authoritative definition of a standard. You may add a passage of up to five words as a Front-Cover Text, and a passage of up to 25 words as a Back-Cover Text, to the end of the list of Cover Texts in the Modified Version. Only one passage of Front-Cover Text and one of Back-Cover Text may be added by (or through arrangements made by) any one entity. If the Document already includes a cover text for the same cover, previously added by you or by arrangement made by the same entity you are acting on behalf of, you may not add another; but you may replace the old one, on explicit permission from the previous publisher that added the old one. The author(s) and publisher(s) of the Document do not by this License give permission to use their names for publicity for or to assert or imply endorsement of any Modified Version. 5. COMBINING DOCUMENTS You may combine the Document with other documents released under this License, under the terms defined in section 4 above for modified versions, provided that you include in the combination all of the Invariant Sections of all of the original documents, unmodified, and list them all as Invariant Sections of your combined work in its license notice. The combined work need only contain one copy of this License, and multiple identical Invariant Sections may be replaced with a single copy. If there are multiple Invariant Sections with the same name but different contents, make the title of each such section unique by adding at the end of it, in parentheses, the name of the original author or publisher of that section if known, or else a unique number. Make the same adjustment to the section titles in the list of Invariant Sections in the license notice of the combined work. In the combination, you must combine any sections entitled "History" in the various original documents, forming one section entitled "History"; likewise combine any sections entitled "Acknowledgements", and any sections entitled "Dedications". You must delete all sections entitled "Endorsements." 6. COLLECTIONS OF DOCUMENTS You may make a collection consisting of the Document and other documents released under this License, and replace the individual copies of this License in the various documents with a single copy that is included in the collection, provided that you follow the rules of this License for verbatim copying of each of the documents in all other respects. You may extract a single document from such a collection, and distribute it individually under this License, provided you insert a copy of this License into the extracted document, and follow this License in all other respects regarding verbatim copying of that document. 7. AGGREGATION WITH INDEPENDENT WORKS A compilation of the Document or its derivatives with other separate and independent documents or works, in or on a volume of a storage or distribution medium, does not as a whole count as a Modified Version of the Document, provided no compilation copyright is claimed for the compilation. Such a compilation is called an "aggregate", and this License does not apply to the other self-contained works thus compiled with the Document, on account of their being thus compiled, if they are not themselves derivative works of the Document. If the Cover Text requirement of section 3 is applicable to these copies of the Document, then if the Document is less than one quarter of the entire aggregate, the Document's Cover Texts may be placed on covers that surround only the Document within the aggregate. Otherwise they must appear on covers around the whole aggregate. 8. TRANSLATION Translation is considered a kind of modification, so you may distribute translations of the Document under the terms of section 4. Replacing Invariant Sections with translations requires special permission from their copyright holders, but you may include translations of some or all Invariant Sections in addition to the original versions of these Invariant Sections. You may include a translation of this License provided that you also include the original English version of this License. In case of a disagreement between the translation and the original English version of this License, the original English version will prevail. 9. TERMINATION You may not copy, modify, sublicense, or distribute the Document except as expressly provided for under this License. Any other attempt to copy, modify, sublicense or distribute the Document is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 10. FUTURE REVISIONS OF THIS LICENSE The Free Software Foundation may publish new, revised versions of the GNU Free Documentation License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. See http:///www.gnu.org/copyleft/. Each version of the License is given a distinguishing version number. If the Document specifies that a particular numbered version of this License "or any later version" applies to it, you have the option of following the terms and conditions either of that specified version or of any later version that has been published (not as a draft) by the Free Software Foundation. If the Document does not specify a version number of this License, you may choose any version ever published (not as a draft) by the Free Software Foundation. ADDENDUM: How to use this License for your documents To use this License in a document you have written, include a copy of the License in the document and put the following copyright and license notices just after the title page: Copyright (c) YEAR YOUR NAME. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.1 or any later version published by the Free Software Foundation; with the Invariant Sections being LIST THEIR TITLES, with the Front-Cover Texts being LIST, and with the Back-Cover Texts being LIST. A copy of the license is included in the section entitled "GNU Free Documentation License". If you have no Invariant Sections, write "with no Invariant Sections" instead of saying which ones are invariant. If you have no Front-Cover Texts, write "no Front-Cover Texts" instead of "Front-Cover Texts being LIST"; likewise for Back-Cover Texts. If your document contains nontrivial examples of program code, we recommend releasing these examples in parallel under your choice of free software license, such as the GNU General Public License, to permit their use in free software.